Shure Product

PSM 200 In Ear Personal Monitoring System

PSM 200 In Ear Personal Monitoring System

The entry to professional in ear personal monitoring from Shure. This package contains SE-112 Sound Isolating earphones, a P2R receiver and a P2T transmixer

The entry to professional in ear personal monitoring from Shure containing all the components you need.

  • Built-in audio limiter
  • Front mounted antenna
  • Two mic/line input channels for mix control
  • Built in headphone limiter
  • Volume control on bodypack receiver
  • 1/2 Rack space

Benefits of In-Ear Monitoring v's a Wedge Speaker 

Using a Shure monitoring system allows you to hear the music via your earphones at the exact time it is played. There can be a short delay in music coming out of the wedge, which can cause performers to play out of time. Wedge monitors will sound fine when standing in one position, but if you move to the left or right, that sound is likely to change. With in ear personal monitoring, the sound will be constant and comes with you, wherever you go. Using wedge monitors long term can also be damaging to your ears. Using Shure sound isolating earphones cuts out the sound around you leaving you to focus on playing in time.

Setting Up a PSM 200 in ear system?

Simply connect two line-level or mic–level inputs directly into the transmixer. Set the frequency on the transmixer using a single button, and the same again on the bodypack receiver. Connect your earphones to the P2R, set up your desired mix using the personal mix controls on the front of the transmixer and you are now all ready to go.
 

The P2T radio TransMixer is a transmitter and mixer in one unit. This forms part of the PSM200 in-ear personal monitoring system
Dual function hybrid in ear personal monitoring receiver - part of the Shure PSM200 series
Entry-level SE112 Sound Isolating Earphones with DynamicDynamic mics have a simple, rugged construction and can handle very high sound pressure levels.Read moreGo to the glossary MicroDriver for great sound with deep bass

Frequency range and power output of the transmitter

Band    

Range            

Power Output

H2

518-554 MHz

30 mW

K9E*

606-638 MHz

30 mW

S5* 

588-865 MHz 

10 mW

*denotes UK frequency band.

Please be aware of country-specific laws when operating on different frequency bands.

  • Environment: Small to medium stages
  • RF Output Power: 10 - 30 mW (countryspecific)
  • Operating Distance: Up to 100m
  • Frequency ResponseThis is the range of frequencies, from the lowest to the highest, that a mic can pick up.Read moreGo to the glossary: 30 Hz - 12 kHz
  • Harmonic distortion: 1.5 % typical
  • Signal-to-noise-ratio: 80 dB (A) typical
  • Listening mode: Mono
  • Compatible Systems per band (up to): 4
  • Transmitter Inputs: 2x XLR/6,3 mm combo, mic/line level
  • Transmitter Outputs: 2x XLR split outputs
  • Wired Bodypack Option: Yes
  • Personal Mix Control: On transmitter
  • Remoteable Transmitter: No
  • Battery Life: Wired: 6 h; Wireless: 4 h

  • Further technical specifications:

    PSM®200 System

    • RF Carrier FrequencyThis is how many times a sound or radio wave oscillates in one second.Read moreGo to the glossary Range: 518­-865 MHz (country dependent)
    • Modulation: FM +/- 35 kHz Deviation (Nominal)
    • Operating Temperature: -7 degrees C to +49 degrees C (+20 degrees F to +120 degrees F) 

    EP2T TransMixer

    • Modulation Limiter: Internal peak limiter (>10:1 hard knee compression)
    • Antenna: 1/4 Wavelength, semi-rigid, PCB Mount
    • Connector Type: XLR/1/4-inch combo
    • Nominal Input Level: - 25 dBu @ 1/2 volume (12 o'clock)
    • Maximum Input Level: - 5 dBu @ 1/2 volume (12 o'clock)
    • Current: 170 mA maximum
    • Dimensions: 220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.)
    • Net Weight: 370 g (13 oz.) 

    P2R Receiver

    • RF SensitivityThis is how mich signal a microphone produces for a given amount of sound.Read moreGo to the glossary: 109 dBm typical
    • Squelch Threshold: 102 dBm typical
    • Antenna: Attached Whip
    • Audio Input Connector: Connector Type: 1/4-inch Mono
    • ImpedanceThis describes how resistant an electrical circuit is to the flow of electricity passing through it.Read moreGo to the glossary: 1 megohm
    • Maximum Input Level: LO = +0 dBu; HI = 10 dBu
    • Frequency ResponseThis is the range of frequencies, from the lowest to the highest, that a mic can pick up.Read moreGo to the glossary: 30 Hz to 20 kHz (+/ 3 dB); earphone dependent
    • Power Requirements: 9 V alkaline battery, Duracell® type MN1604 recommended
    • Audio Output Connector: 1/8 inch (3.5 mm)
    • Minimum Load ImpedanceThis describes how resistant an electrical circuit is to the flow of electricity passing through it.Read moreGo to the glossary: 8 ohms
    • Net Weight: 100 g (3.52 oz.), less battery
    • Overall Dimensions: 122 mm x 73 mm x 32 mm (4.809 in. x 2.875 in. x 1.251 in.)

     SE112 Earphones

    • FrequencyThis is how many times a sound or radio wave oscillates in one second.Read moreGo to the glossary Range: 25Hz – 17.5kHz
    • SensitivityThis is how mich signal a microphone produces for a given amount of sound.Read moreGo to the glossary: 108 dB SPL/mW (@ 1kHz)
    • ImpedanceThis describes how resistant an electrical circuit is to the flow of electricity passing through it.Read moreGo to the glossary: 16 Ohms (@ 1kHz)
    • Input Connector: 3.5mm (1/8”)
    • Colour: Gray 
    • Cable Length: 127 cm (64”)
Allows user to mix an ambient signal to their in-ear monitor mix.

PS9

Battery Adaptor for connection to a Shure PS41 AC Adaptor (included) via a threaded DC connector. Use with Shure models P2R, P4R, P4HW, T1, T1G, LX1, UT1, ULX1, MX1BP and VP3.
Splitter cable for wired use of instruments with the P2R Hybrid Bodypack receiver.
PA200 series splitter cables split the signal from an instrument for connection to a P2R receiver and a wireless transmitter simultaneously. Three splitter cable models are available to allow compatibility with all Shure wireless bodypack transmitters.
PA200 series splitter cables split the signal from an instrument for connection to a P2R receiver and a wireless transmitter simultaneously. Three splitter cable models are available to allow compatibility with all Shure wireless bodypack transmitters.
The PS124 In-Line Power Supply was developed to work with various rack-mountable Shure wireless receivers and/or PSM transmitters. It consists of the current PS45 In-Line Power Supply with a powersplitter attachment cable that allows for four power connections via a single in-line power supply.
In-line power supply (230V) for 200M, FP22, FP24, FP33 Mixer, SLX4, PGX4, ET4, EUT4, PG4 and PG88 receiver.
Yellow Foam Sleeves for Shure Sound Isolating Earphones. 5 pairs.
Yellow Foam Sleeves for Shure Sound Isolating Earphones. 50 pairs.
Gray Soft Flex Sleeves for Shure Sound Isolating Earphones. 5 pairs.
Triple Flange Sleeves for Shure Sound Isolating Earphones. Package of 6.
Black Foam Sleeves for Shure Sound Isolating Earphones. 5 pairs.

URT

Rack tray for up to two PG4, PGX4, T4A, T4N, UT4 and UT4A receivers.
Universal Mounting Bracket for Connecting two different half-rack products. (eg: DFR11EQ to UC4, P4M to P6T)
Neoprene Belt Pouch for Shure wireless bodypack transmitters LX1, SC1, SLX1, T1G, T1, U1, UC1, ULX1, UT1, PGX1
Neoprene bodypack arm pouch for all Shure bodypack transmitters.